Residential · San Francisco, CA
Apex Asphalt San Francisco has served San Francisco since 2017, installing and repairing asphalt walkway surfaces that stay smooth, safe, and easy to maintain. From new paths to full tear-outs and patching, we build pedestrian-grade asphalt that drains correctly and holds up to daily traffic.
Good asphalt walkway work starts below the surface. We begin with layout, demolition if needed, and proof-rolling to find soft spots, then undercut unstable subgrade and rebuild with compacted Class 2 aggregate base. Base depth is matched to use and soil conditions (typically 3-6 inches for pedestrian paths), compacted in lifts with a plate compactor or small roller to meet density, then graded for proper pitch. Before paving, we set forms, establish transitions at steps, gates, and landings, and install geotextile fabric where separation is needed to reduce base pumping and settlement.
San Francisco’s microclimates, shade, and frequent moisture demand clean drainage and a tight surface. We pave with hot-mix asphalt, place consistent lift thickness (often 1.5-2 inches compacted for walkways), and compact to eliminate raveling and early cracking. For safer footing, we can add a fine texture (tight mat with clean edges) and dial in cross-slope to move water off the path without creating a trip hazard. Repairs focus on correcting the cause, not just covering symptoms, including saw-cut patching, infrared-style blending where appropriate, crack sealing with hot pour rubberized sealant, and correcting birdbaths that lead to algae and slick spots.
San Francisco customers choose us because we treat walkways like finish work, not leftover paving. Crews protect adjacent landscaping and concrete with clean saw cuts, controlled excavation, and careful edge work, then tie new asphalt into existing slabs, curbs, and pavers without jagged lips. You get clear recommendations on when to patch, when to resurface, and when a full remove-and-replace is the only economical option. As a licensed and insured asphalt contractor, we show up with the right equipment, keep the site orderly, and provide a written scope so expectations are set before the first cut.
At completion we do a final walkthrough, checking slope, smoothness, and transitions at doors, stairs, and utility covers. You receive care guidance, including cure time, when to allow foot traffic, and when to schedule sealcoating (typically after the asphalt has cured, around 6-12 months depending on conditions). For repair projects, we document what was corrected, such as base failure, edge breakdown, or water intrusion, so future maintenance is straightforward. The result is an asphalt walkway that looks clean, drains correctly, and stays serviceable with simple periodic crack sealing and sealcoat maintenance.
Yes. We are a licensed and insured asphalt contractor, and we provide written estimates with a clear scope of work, materials, and scheduling.
Light foot traffic is often possible the same day, while vehicle traffic typically needs more time depending on temperature, thickness, and site conditions. We give specific reopen times and protect soft edges during the first days of curing.
Yes, when failures are isolated. We can sawcut and remove damaged sections, rebuild base, and place hot-mix asphalt patches, then blend with crack sealing or a resurfacing plan if the surrounding pavement is near end-of-life.
Yes. We can stripe with traffic paint or thermoplastic where appropriate and help you plan stall widths, accessible spaces, and access aisles based on current site conditions and striping best practices.
Keep water moving off the surface, seal cracks early, avoid turning wheels in place when the pavement is hot, and schedule sealcoating on a maintenance cycle after proper cure. We can set a maintenance plan based on your traffic and exposure.
An asphalt walkway is a cost-effective way to create a smooth, accessible path from sidewalks to entries, between buildings, or through shared outdoor areas. Apex Asphalt San Francisco installs new walkway paving and fixes failing paths by addressing the base, drainage, and surface wear that cause cracking, raveling, and low spots. Whether you need a short connector path or a long circulation route, we build pedestrian-friendly asphalt with clean edges and consistent slope for reliable drainage.
Walkway problems usually start with the base or drainage. If water is trapped under the asphalt, the subgrade softens, the base pumps, and the surface eventually alligators, settles, or breaks at the edges. Our process focuses on restoring structure first, including undercutting soft areas, installing geotextile fabric when separation helps, rebuilding the aggregate base in compacted lifts, and grading to a stable pitch. Once the base is right, the asphalt mat stays tight and resists early cracking and raveling.
For new asphalt walkway installation, we handle layout, grading, forming, and tie-ins to existing concrete, curbs, and pavers. Typical walkway sections are built with a compacted aggregate base and a hot-mix asphalt surface course, compacted with a vibratory plate and small roller to lock in density. If the site calls for it, we can integrate drainage details such as correcting low areas (birdbaths) and improving cross-slope to move water off the walking surface without creating uncomfortable side-to-side tilt.
If you are deciding between patching, resurfacing, or replacement, we will provide a written recommendation based on what we find in the subgrade and base, not guesswork. The goal is a safe, clean-looking asphalt walkway that holds up to daily foot traffic and stays easy to maintain with periodic crack sealing and sealcoating at the right interval.
Call now or send a request and we will reach out within one business day to schedule your free, no-obligation estimate in San Francisco. We assess the project, review the details, and give you a written quote before any work starts, so you know exactly what to expect.
Prefer to write? Contact us or head back to the home page.
